Difference between revisions of "Electronics and Rapid Prototyping"

From MakeICT Wiki
Jump to navigationJump to search
(Undo revision 6428 by Christian Kindel (talk))
Line 73: Line 73:
 
| [[File:Soldering Iron.jpg|200px]] || [[media:Soldering Tips.pdf|Soldering iron]] ||Various || Various || 110 || Working || [[User:James A Seymour|James Seymour]]
 
| [[File:Soldering Iron.jpg|200px]] || [[media:Soldering Tips.pdf|Soldering iron]] ||Various || Various || 110 || Working || [[User:James A Seymour|James Seymour]]
 
|-
 
|-
| [[File:RD500 II photo.jpg|200px]] || Rework System ||Den-on Instruments || [[media:RD-500 II rework station manual.pdf|RD-500S II]] || 110 || Not yet || [[User:James A Seymour|James Seymour]]
+
| [[File:TEK1240.jpg|200px]] || [[Logic Analyzer]] ||Tektronix || 1240|| 110 || Working || [[User:James A Seymour|James Seymour]]
|-
 
| [[File:TEK1240.jpg|200px]] || [[media:RD-500 II rework station manual.pdf|Logic Analyzer]] ||Tektronix || 1240|| 110 || Working || [[User:James A Seymour|James Seymour]]
 
 
|-
 
|-
 
| [[File:TEK492P.jpg|200px]] || [[Tektronix 492 AP|Oscilliscope]] ||Tektronix || 492P || 110 || Working || [[User:James A Seymour|James Seymour]]
 
| [[File:TEK492P.jpg|200px]] || [[Tektronix 492 AP|Oscilliscope]] ||Tektronix || 492P || 110 || Working || [[User:James A Seymour|James Seymour]]

Revision as of 15:03, 8 August 2019

Attention! This page or section is out of date. Help us out by modifying this page.
Details: missing details and access policies


General Information

MakeICT's Electronics and Rapid Prototyping lab is an enclosed 200 sq ft area. This area has several dedicated spaces. One is for creation of electronics, including a board milling machine, area dedicated for assembly, and reflow oven. Another is for the troubleshooting of electronics, including a hot air rework station, Spectrum Analyzer, Oscilloscope, current limited power supply, and logic analyzer. We have a pair of CNC machines fully capable of handling wood, and some aluminum. We offer Dremmel sets to handle less delicate work (or more delicate depending on your skill.) We also have systems one can check out for the learning of electronics, toolsets to fix and repair, as well as Chip programmers, a bus pirate, Raspberry Pis, Arduinos, even a pic based USB module. We offer a full components library, resplendent with analogue devices, TTL type logic, some rare chipsets, and a full complement of passives. This lab is dedicated to creating and debugging electronics, as well as some rapid prototyping capabilities. Never a room to be bored in, the common complaint in this room is, "what do I make first?"

The Area Lead over the electronics and rapid prototyping lab is Mark Satoria.

Equipment Access Policy

THIS POLICY IS NOT YET APPROVED OR OFFICIAL and is under construction

CNC MACHINES

All Equipment

  • Equipment requiring authorization may be operated by an unauthorized user only under the direct supervision of an authorized user.

Scopes

MakeICT has a few Oscilloscopes. Most notably is the Tektronix 465B We are fortunate to have some nice ones. Using the Oscilloscope takes some finesse and it's best you have some help with it if you're fairly new to one, so we require certification. The Oscilloscope shows Voltage over time, similar to a graph. There is lots of settings, dials, and switches. if you want to learn to use it just ask to be taught from a reasonably knowledgeable member.

Spectrum Analyzer

We have a very nice Spectrum Analyzer (Tektronix 492 AP). The Spectrum Analyzer shows receive power over frequency. So if you set it properly you would see Peaks where each Wifi network is transmitting. It is easy (and expensive) to damage the input of a Spectrum Analyzer. We ask you are certified and use proper caution. We have several attenuators available for impedance matching, so use them.


'The Beast' RD-500S II rework Machine

The Beast isn't up and running yet. It requres some TLC and is considered a work in progress. Once operational, it is designed to make short work of SMD replacement, by combining a CNC rework station with an on board reflow process. Operation will be mostly peer Certification.

ERP SAFETY

We prefer a solid understanding of the equipment you are using before use. Certain pieces of equipment are expensive and not easily repaired. Some pieces of equipment can seriously injure or kill you. It never hurts to run what your doing by someone. There are some dangerous pieces of equipment that can burn mutilate or electrocute. These require peer authorization, for the user's safety. SAFE OPERATION of equipment is top priority.

To protect members, any project that exceeds 50V must be clearly labeled "DANGER HIGH VOLTAGE" and will not be left powered up unattended unless wiring is inaccessible to accidental contact. Additionally, the building power panel located on the north wall is considered off limits to members unless they are board appointed personnel. When in doubt, ask.

We strongly suggest that while machining tools are in operation, anyone entering that part of the shop use personal protective equipment (PPE) such as safety glasses, hearing protection, and hand protection.

Finally, is HIGHLY recommended that we use a buddy system, where no single person is working in the shop without a second person in the building so that if there is an injury, somebody else is there to call for help or assist you.

Borrowing Items

Currently we do not lend out equipment, but as we build up an inventory of certain items, we may allow checkout similar to a library. Special arrangements may be made on a individual basis, but that is entirely up to the Area Lead.

Items for Purchase

We do have certain items for sale, such as Breadboards. Sales should be considered final, the money goes back into the ERP Lab.

Component Library

MakeICT maintains an electronics library. There is currently an inventory of available active components. This inventory is maintained by volunteers, we ask that you record components you are removing or adding on the clipboard, so that they can be included/subtracted from the inventory. Inventory management is to help the membership, and must rely on the membership. Components in the library are for member use, We only ask you put a buck or two in the donation bucket if you use a lot of them, or some of the rare/complex parts.

Many of our devices come from dubious sources, MakeICT makes no claim as to their datasheet capabilities, and a certain amount of derateing may be required.

Classes

Electronics and Rapid Prototyping Safety

  1. Do not use any machine you are not trained on and comfortable using. If at any time you are unsure of what you are doing, stop immediately and ask for help.
  2. Do not use any machine that is not in good working order. Stop, unplug and leave a note on the machine and notify the Area Lead.
  3. NEVER ASSUME A TOOL IS PROPERLY ADJUSTED. Always check the tool prior to use.
  4. NEVER MODIFY OR HACK MACHINERY WITHOUT CONSENT FROM THE AREA LEAD.
  5. Always triple check your inputs when connecting to equipment. Dangerous levels are dangerous.

Equipment List

Picture What Manufacturer Model Power Status Expert
Soldering Iron.jpg Soldering iron Various Various 110 Working James Seymour
TEK1240.jpg Logic Analyzer Tektronix 1240 110 Working James Seymour
TEK492P.jpg Oscilliscope Tektronix 492P 110 Working James Seymour
TEK465B.jpg Oscilloscope Tektronix 465B 110 Working James Seymour
Fluke 867.jpg Graphical Multimeter Fluke 867 9V Working James Seymour
Fluke 117.jpg True RMS Non-contact Multimeter Fluke 117 9V Working James Seymour
Fluke 80K-40.jpg High Voltage Probe Fluke 80K-40 NA Working James Seymour
Fluke 80i-1010.jpg Clamp on DC/AC Current Probe]] Fluke 80i-1010 1-1000 Adc, 1-600Aac (1 mV/A) Working James Seymour
QS-5100.jpg Lead Free Reflow Oven Qinsi Technology QS-5100 110 Working James Seymour
Arksen992D.jpg Soldering Station with Heat Gun Arksen 992D 110 Working James Seymour
Board Goblin.jpg Board Goblin-Circuit Board Mill Tom McGuire 47158 110 Working Tom McGuire
Fireball v90.jpg CNC Mill Probotix Fireball V90 110 Not Working Tom McGuire
Sherline 5400 Mill.jpg CNC Mill Sherline Sherline CNC Mill 110 Working James Lancaster Christian Kindel
CSI Speco PSV5.jpg Variable power supply SPECO PSV-5 110 Under Repair SPECO PSV-5 repair log James Seymour
UDB100X.jpg 5Mhz Tone Generator MingHe UDB1005S 110 In-Work Mike Barushok
DOA-P701-AA.jpg Vacuum Pump Gast DOA-P701-AA 110 Working James Seymour
  • Policies may change with the needs of the department and may go into affect before this page is updated to reflect it.