Difference between revisions of "LASER Cutter Materials"
From MakeICT Wiki
Jump to navigationJump to search| Line 30: | Line 30: | ||
|- | |- | ||
| Leather, suede || x || x || || || | | Leather, suede || x || x || || || | ||
| + | |- | ||
| + | | Magnetic sheet || x || x || || Cuts easily || | ||
|- | |- | ||
| Marble || x || || || || | | Marble || x || || || || | ||
| Line 37: | Line 39: | ||
| Melamine || x || x || || || | | Melamine || x || x || || || | ||
|- | |- | ||
| − | | Mylar || x || x || | + | | Mylar || x || x || 1/16" || Works well if it's thin. Thick mylar has a tendency to warp, bubble, and curl || Gold coated mylar will not work |
|- | |- | ||
| Paper, card stock || x || x || thin || || | | Paper, card stock || x || x || thin || || | ||
| Line 45: | Line 47: | ||
| Rubber || x || x || || || | | Rubber || x || x || || || | ||
|- | |- | ||
| − | | Wood || x || x || | + | | Tile || x || || |
| + | |- | ||
| + | | Wood || x || x || 1/4" || Avoid oily/resinous woods || FIRE - Cutting oily woods, or very resinous woods can catch fire. | ||
|- | |- | ||
| Wood Veneer || x || x || || || | | Wood Veneer || x || x || || || | ||
| Line 52: | Line 56: | ||
'''Approved Metal Materials''' | '''Approved Metal Materials''' | ||
| + | |||
{| class="wikitable sortable" | {| class="wikitable sortable" | ||
|- | |- | ||
| Line 57: | Line 62: | ||
|- | |- | ||
| Painted Metals || x || || | | Painted Metals || x || || | ||
| − | |||
| − | |||
|- | |- | ||
| Bare Metals || x || || | | Bare Metals || x || || | ||
|- | |- | ||
| − | | Anodized Aluminum || x || || | + | | Anodized Aluminum || x || || Vaporizes the anodization away |
|- | |- | ||
| Brass || x || || | | Brass || x || || | ||
Revision as of 05:28, 18 October 2015
Approved Organic Materials
If your material is not on the list, check with Mike
| Name | Engrave | Cut | Max thickness | Notes | WARNING |
|---|---|---|---|---|---|
| Acrylic (aka Lucite, Plexiglas, PMMA) | x | x | 1/2" | Cuts well, leaves a smooth polished edge. Higher powers can leave smoke/scorch marks along edges | |
| Cardboard, cartons | x | x | thicker | Cuts well, can catch fire | FIRE hazard! |
| Ceramic | x | ||||
| Cloth (cotton, felt, hemp) | x | x | Cuts easily | NO plastic coated or impregnated cloth! | |
| Corian | x | x | |||
| Cork | x | x | 1/4" | Cuts nicely, the quality of the cut depends on the thickness and quality of the cork. Engineered cork has a lot of glue in it, may not cut nicely. | |
| Delrin | x | x | |||
| Fabric (polyester) | x | x | |||
| Fiberglass | x | x | |||
| Glass | x | ||||
| Leather, suede | x | x | |||
| Magnetic sheet | x | x | Cuts easily | ||
| Marble | x | ||||
| Matte Board | x | x | |||
| Melamine | x | x | |||
| Mylar | x | x | 1/16" | Works well if it's thin. Thick mylar has a tendency to warp, bubble, and curl | Gold coated mylar will not work |
| Paper, card stock | x | x | thin | ||
| Pressboard | x | x | |||
| Rubber | x | x | |||
| Tile | x | ||||
| Wood | x | x | 1/4" | Avoid oily/resinous woods | FIRE - Cutting oily woods, or very resinous woods can catch fire. |
| Wood Veneer | x | x |
Approved Metal Materials
| Name | Engrave | Cut | Notes |
|---|---|---|---|
| Painted Metals | x | ||
| Bare Metals | x | ||
| Anodized Aluminum | x | Vaporizes the anodization away | |
| Brass | x | ||
| Coated Metals | x | ||
| Stainless Steel | x | ||
| Titanium | x |
- CO2 lasers will engrave metals when coated with an added metal marking solution.
