Woodshop Area
Details: missing details and access policies
Contents
General Information
MakeICT's woodshop is an enclosed 32'x36'(1152 sq ft) air conditioned area dedicated to wood working.
Mike Hutton is the Benevolent Dictator over the woodshop.
The goal of the shop space is to encourage continued learning of the skills needed to further your knowledge of woodworking!
Machine Access Policy
Under Construction!,
Because of the hazardous nature of these tools, before anyone can use the tools, they must pass a shop safety course. We want everyone to go home safe and in one piece! SAFE OPERATION of tools is top priority.
Anyone entering the shop will be required to use personal protective equipment (PPE) such as safety glasses, hearing protection, and possibly dust masks (these will be for available for purchase).
Only new domestic lumber will be allowed in the shop, treated lumber is hazardous. Some people are alergic to certain lumber and have become sensitized to being near the materials, therefore no exotic lumber will be allowed in the shop to protect all members. No used or recycled wood products will be allowed to protect machinery as well as to protect other members. When in doubt, ask.
I HIGHLY recommend that we use a buddy system, where no single person is working in the shop without a second person in the building so that if there is an injury, somebody else is there to call for help or assist you.
General Shop Safety
1. Do not use any machine you are not trained on and comfortable using. If at any time you are unsure of what you are doing, stop immediately and ask for help. Do not force tools.
2. Do not use any machine that is not in good working order. Stop, unplug and leave a note on the machine and notify the woodshop BD.
3. Wear safety glasses at all times when in the shop area, including near the machine shop.
4. Ear protection is also recommended, many of the tools operate above 90 decibels and without protection, you are losing hearing.
5. When using power tools (including hand power tools):
▪ No open-toed shoes or loose clothing (remove drawstrings) ▪ Remove objects on hands and wrists (including rings, bracelets, & watches) ▪ Remove dangly necklaces, hair ornaments, and earrings ▪ Restrain long hair to prevent entanglement ▪ Do not wear gloves
6. Do not leave machines running unattended.
7. Most shop accidents are caused by working tired, rushed or distracted. As you get more experience, you will learn to listen to the little voice in the back of your mind that says, you probably shouldn't do that. Stop and think, there is usually a safer way of performing that function. These machines do not have a brain, please use yours!
Woodshop Specific Safety
- All powered woodcutting and sanding tools must be run with dust collection or vacuum equipment connected to the appropriate ports and on at all times. Do not cycle the dust collector on and off, if you are planning on working with multiple tools, leave the collector on (short cycling will overheat the motor).
- Smoke or sparks are bad signs in the woodshop. Stop what you are doing and correct the problem. Usually correct feed and depth of cut or getting a sharp bit / blade will help.
- No metal cutting allowed on woodshop equipment.
- No wet or damp items of any type (including drink containers, rags, or hands) may be placed or left on machine surfaces as they will corrode.
- Clean your machines, your work space, and put all tools away when finished. Scrap wood should be placed in designated locations. Use vacuums or hand brushes to clean machinery.
- All guests are the responsibility of the member, guests are not allowed to use equipment. This is a working shop, so children less than 7 years old are not allowed for safety.
- Member will be responsible for replacing the blade and Sawstop brake if the brake is fired.
This is a video on table saw kickback. Do not try this in the woodshop!
Equipment List
Picture | What | Manufacturer | Model | Power | Status | Expert | How To |
---|---|---|---|---|---|---|---|
10" Cabinet Table Saw | Saw Stop | Professional PCS31230 | 220 | Setup | Mike H. | manual | |
8" Carbide Helical Head Jointer | Shop Fox | W1741S | 220 | Setup | Mike H. | manual | |
15" Carbide Helical Head Planer | Jet | JWP-15HH | 220 | Setup | Mike H. | manual | |
17" Drill Press with laser | Jet | JDP-17DX | 110 | Setup | Mike H. | ||
Oscillating Spindle Sander | Jet | JBOS-5 | 110 | To Setup | Mike H. | manual | |
Low Speed 8" Bench Grinder | Jet | JWBG-8 | 110 | To Setup | Mike H. | manual | |
Tool Sharpener | Work Sharp | WS3000 | 110 | To Setup | Mike H. | User's Guide | |
Cyclone Dust Collector | Oneida Air | 5HP Super Dust Gorilla | 220 | Setup | Mike H. | Owner's Manual | |
Scroll Saw | Dewalt | DW788 | 110 | Setup | Mike H. | File:383329-00,DW788.pdf | |
2.25HP Router | Bosch | 1617EVSPK | 110 | Setup | Mike H. | File:BoschRouterManual.pdf | |
2" 18Gauge Finish Nailer | Hitachi | NT50AE2 | Air | Setup | Mike H. | Owner's Manual | |
Router Table with JessEm Lift | Porter Cable | 7518 | 110 | Setup | Mike H. | File:PorterCable7518OwnerManual.pdf | |
12" Double Bevel Miter Saw | Dewalt | DW705 | 110 | Setup | Mike H. | File:DewaltDW705OwnerManual.pdf | |
6x48 Belt/12 Disc sander | PowerMatic | 30b | 110 | Setup | Mike H. | ||
12x36 Wood Lathe | Rockwell | 110 | One Setup | Mike H. |