Difference between revisions of "FabLab Area"

From MakeICT Wiki
Jump to navigationJump to search
Line 50: Line 50:
 
# Do not use any machine you are not trained on and comfortable using. If at any time you are unsure of what you are doing, stop immediately and ask for help.
 
# Do not use any machine you are not trained on and comfortable using. If at any time you are unsure of what you are doing, stop immediately and ask for help.
 
# Do not use any machine that is not in good working order. Stop, unplug and leave a note on the machine and notify the FabLab BD OR Mike Doolittle.
 
# Do not use any machine that is not in good working order. Stop, unplug and leave a note on the machine and notify the FabLab BD OR Mike Doolittle.
# NEVER ASSUME A TOOL IS PROPERLY ADJUSTED. Always check the tool prior to use.
+
# '''NEVER ASSUME A TOOL IS PROPERLY ADJUSTED.''' Always check the tool prior to use.
# NEVER MODIFY OR HACK THE 3D PRINTER, FOAM CUTTER OR LASER CUTTER.
+
# '''NEVER MODIFY OR HACK THE 3D PRINTER, FOAM CUTTER OR LASER CUTTER.'''
  
 
== Equipment List ==
 
== Equipment List ==

Revision as of 12:24, 18 October 2015

Attention! This page or section is out of date. Help us out by modifying this page.
Details: missing details and access policies


General Information

MakeICT's FabLab is an open 300 sq ft area dedicated to fabrication and rapid prototyping. Here is where you can test ideas, and concepts before moving on to more expensive materials or processes. Or, simply enjoy the creative process and see what you can make. The FabLab currently houses 3D printers, foam cutter, and LASER engraver/cutter.

Per MakeICT policy, all machinery and tools require prior instruction and certification before use. We want all our members and guests to be safe, and the equipment kept in top condition so all can enjoy.

Bryan Barr is the Benevolent Dictator over the FabLab.

Classes

Machine Access Policy

DRAFT (currently under review)

DO NOT USE NON-APPROVED MATERIALS!

Clean up! Users are responsible for clean up after themselves; failure to which may result in loss of FABLAB Privileges.

3D Printers

Use of the 3D printers requires attendance in a 3D printer certification workshop or certification from an approved peer-certifier.

  • Any member who has been certified to use the 3D printer may peer-certify other members
  • Certification instruction must at least include
    • Fundamental knowledge of each printer's working principles
    • Proper use and control of each printer
    • Software workflow
    • How to change filament
    • How to pay for material
  • Certification must be documented (link to instructions or form) prior to use
  • List of 3D Printer approved users is listed below

Foam Cutter

Use of the foam cutter requires attendance in a foam cutter certification workshop or certification from an approved peer-certifier.

  • Any member who has been certified to use the foam cutter may peer-certify other members
  • Certification instruction must at least include
    • Fundamental knowledge of foam cutter's working principles
    • Proper use and control of foam cutter
    • Software workflow
  • Certification must be documented (link to instructions or form) prior to use
  • List of Foam Cutter approved users is listed below

LASER Cutter

Use of the LASER cutter requires attendance in LASER Cutter Basics Class

  • Certification must be documented (link to instructions or form) prior to use
  • List of LASER Cutter approved users is listed below

FabLab Area Safety

  1. Do not use any machine you are not trained on and comfortable using. If at any time you are unsure of what you are doing, stop immediately and ask for help.
  2. Do not use any machine that is not in good working order. Stop, unplug and leave a note on the machine and notify the FabLab BD OR Mike Doolittle.
  3. NEVER ASSUME A TOOL IS PROPERLY ADJUSTED. Always check the tool prior to use.
  4. NEVER MODIFY OR HACK THE 3D PRINTER, FOAM CUTTER OR LASER CUTTER.

Equipment List

Picture What Manufacturer Model Power Status Expert How To
RostockBlack-V2-Front.jpg 3D Printer SeeMeCNC Rostock Max v2 110 Working Bryan Barr
3D-Printer.jpg 3D Printer RepRap 110 Working James Lancaster
Ultimaker II.jpeg 3D Printer Ultimaker Ultimaker II 110 Working Tom McGuire
Foam-Cutter.jpg Foam Cutter Tom McGuire 110 Working Tom McGuire
Laser cutter.jpg LASER Cutter Rabbit Laser QX1290 230 Working Mike Doolittle

3D Printer Users (to be changed to Certified Users once approved)

Name Notes Certification Date Peer Certified Name
Bryan Barr FabLab BD
James Lancaster 3D Printer instructor
Mike Doolittle Classroom BD
Dustin Richey
Dom Carnare Mentor
Tom McGuire Mentor
Kip Landwehr Mentor
Jeff Eck

3D Printer Maintenance Technicians

Name Notes
Bryan Barr FabLab BD
James Lancaster 3D Printer instructor
Tom McGuire Mentor

Foam Cutter Users (to be changed to Certified Users once approved)

Name Notes Certification Date
Bryan Barr FabLab BD
Tom McGuire Foam Cutter instructor
Dom Canare

Foam Cutter Maintenance Technician

Name Notes
Tom McGuire Foam Cutter instructor

LASER Cutter Approved Users (to be changed to Certified Users once approved)

Name Notes Certification Date
Bryan Barr FabLab BD
Mike Doolittle LASER Cutter instructor
John Alexander
Jerry Carpenter Mentor
David Springs
William Davisson
Brad Cooley
Ivan Quiroz
Jonny Fosnight
Stephen Reckers
Mike Hutton Woodshop BD

LASER Cutter Maintenance Technicians

Name Notes
Bryan Barr FabLab BD
Mike Doolittle LASER Cutter instructor
Jerry Carpenter Mentor