Slic3r config 12-12-16
From MakeICT Wiki
Jump to navigationJump to search
# generated by Slic3r 1.2.9 on Mon Dec 12 15:14:13 2016 [filament:RepRap Ninjaflex] bed_temperature = 0 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 3 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.75 first_layer_bed_temperature = 0 first_layer_temperature = 210 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 10 slowdown_below_layer_time = 5 temperature = 210 [filament:RepRap PLA] bed_temperature = 60 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 3 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.75 first_layer_bed_temperature = 60 first_layer_temperature = 200 max_fan_speed = 100 min_fan_speed = 35 min_print_speed = 10 slowdown_below_layer_time = 5 temperature = 200 [filament:Rostock ABS] bed_temperature = 80 bridge_fan_speed = 100 cooling = 1 disable_fan_first_layers = 3 extrusion_multiplier = 1 fan_always_on = 0 fan_below_layer_time = 30 filament_colour = #FFFFFF filament_diameter = 1.75 first_layer_bed_temperature = 80 first_layer_temperature = 225 max_fan_speed = 100 min_fan_speed = 41 min_print_speed = 10 slowdown_below_layer_time = 10 temperature = 220 [filament:Rostock PLA] bed_temperature = 60 bridge_fan_speed = 100 cooling = 0 disable_fan_first_layers = 3 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.75 first_layer_bed_temperature = 60 first_layer_temperature = 215 max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 10 slowdown_below_layer_time = 10 temperature = 210 [filament:Rostock PLA - Wood] bed_temperature = 60 bridge_fan_speed = 100 cooling = 0 disable_fan_first_layers = 3 extrusion_multiplier = 1 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.75 first_layer_bed_temperature = 60 first_layer_temperature = 215 max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 10 slowdown_below_layer_time = 10 temperature = 200 [filament:Ultimaker ABS] bed_temperature = 80 bridge_fan_speed = 100 cooling = 0 disable_fan_first_layers = 3 extrusion_multiplier = 0.93 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FF1100 filament_diameter = 1.75 first_layer_bed_temperature = 80 first_layer_temperature = 240 max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 10 slowdown_below_layer_time = 5 temperature = 240 [filament:Ultimaker PLA] bed_temperature = 60 bridge_fan_speed = 100 cooling = 0 disable_fan_first_layers = 3 extrusion_multiplier = 0.9 fan_always_on = 1 fan_below_layer_time = 60 filament_colour = #FF1100 filament_diameter = 1.75 first_layer_bed_temperature = 60 first_layer_temperature = 215 max_fan_speed = 100 min_fan_speed = 100 min_print_speed = 10 slowdown_below_layer_time = 5 temperature = 210 [presets] filament = Ultimaker PLA.ini print = Ultimaker 2.ini printer = Ultimaker 2.ini [print:RepRap] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 50% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 25% fill_pattern = rectilinear first_layer_acceleration = 0 first_layer_extrusion_width = 200% first_layer_height = 0.35 first_layer_speed = 30 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 80 interface_shells = 0 layer_height = 0.25 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 20 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 3 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 6 skirt_height = 1 skirts = 2 small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 60 support_material_threshold = 0 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 15 top_solid_layers = 5 travel_speed = 80 xy_size_compensation = 0 [print:RepRap.old] avoid_crossing_perimeters = 0 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 50% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 25% fill_pattern = rectilinear first_layer_acceleration = 0 first_layer_extrusion_width = 200% first_layer_height = 0.35 first_layer_speed = 30 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 60 interface_shells = 0 layer_height = 0.25 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 30 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 40 perimeters = 3 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 6 skirt_height = 1 skirts = 2 small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 60 support_material_threshold = 0 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0 top_solid_infill_speed = 15 top_solid_layers = 5 travel_speed = 80 xy_size_compensation = 0 [print:Rostock] avoid_crossing_perimeters = 1 bottom_solid_layers = 2 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 45 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 50% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 25% fill_pattern = rectilinear first_layer_acceleration = 0 first_layer_extrusion_width = 200% first_layer_height = 0.35 first_layer_speed = 15 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 20 infill_speed = 40 interface_shells = 0 layer_height = 0.2 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 25 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 30 perimeters = 3 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 6 skirt_height = 1 skirts = 1 small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 40 support_material_threshold = 0 thin_walls = 1 threads = 5 top_infill_extrusion_width = 0 top_solid_infill_speed = 30 top_solid_layers = 4 travel_speed = 150 xy_size_compensation = 0 [print:Ultimaker 2] avoid_crossing_perimeters = 1 bottom_solid_layers = 3 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 45 brim_width = 0 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0.4 external_perimeter_speed = 50% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0.4 fill_angle = 45 fill_density = 20% fill_pattern = rectilinear first_layer_acceleration = 0 first_layer_extrusion_width = 110% first_layer_height = 0.2 first_layer_speed = 15 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0.4 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 20 infill_speed = 45 interface_shells = 0 layer_height = 0.2 max_print_speed = 80 max_volumetric_speed = 0 min_skirt_length = 10 notes = only_retract_when_crossing_perimeters = 0 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0.4 perimeter_speed = 30 perimeters = 2 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 6 skirt_height = 1 skirts = 2 small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0.4 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 40 support_material_threshold = 0 thin_walls = 1 threads = 2 top_infill_extrusion_width = 0.4 top_solid_infill_speed = 30 top_solid_layers = 5 travel_speed = 150 xy_size_compensation = 0 [print:Wood] avoid_crossing_perimeters = 1 bottom_solid_layers = 2 bridge_acceleration = 0 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 2 complete_objects = 0 default_acceleration = 0 dont_support_bridges = 1 external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 50% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extrusion_width = 0 fill_angle = 45 fill_density = 25% fill_pattern = rectilinear first_layer_acceleration = 0 first_layer_extrusion_width = 200% first_layer_height = 0.35 first_layer_speed = 15 gap_fill_speed = 20 gcode_comments = 0 infill_acceleration = 0 infill_every_layers = 1 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 20 infill_speed = 80 interface_shells = 0 layer_height = 0.2 max_print_speed = 70 max_volumetric_speed = 0 min_skirt_length = 25 notes = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 3 post_process = raft_layers = 0 resolution = 0 seam_position = aligned skirt_distance = 6 skirt_height = 1 skirts = 1 small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 60 support_material_threshold = 0 thin_walls = 1 threads = 5 top_infill_extrusion_width = 0 top_solid_infill_speed = 80% top_solid_layers = 4 travel_speed = 150 xy_size_compensation = 0 [printer:Reprap] bed_shape = 0x0,200x0,200x200,0x200 before_layer_gcode = end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nG1 \nM84 ; disable motors\n extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.35 octoprint_apikey = E2758749A97D42DFAD2F2F2480ACFAF3 octoprint_host = 192.168.9.119 pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 0 retract_length = 2 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 40 start_gcode = G28 ; home all axes\n;Next line shouldn't be needed.\n;G92 Z109; Correct Z, since we home at Zmax\nG1 Z5 F150 ;bring the nozzle down to just off the bed. \n toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 z_offset = 0 [printer:Rostock] bed_shape = 129.288x13.5887,127.159x27.0285,123.637x40.1722,118.761x52.8758,112.583x65,105.172x76.4121,96.6088x86.987,86.987x96.6088,76.4121x105.172,65x112.583,52.8758x118.761,40.1722x123.637,27.0285x127.159,13.5887x129.288,0x130,-13.5887x129.288,-27.0285x127.159,-40.1722x123.637,-52.8758x118.761,-65x112.583,-76.4121x105.172,-86.987x96.6088,-96.6088x86.987,-105.172x76.4121,-112.583x65,-118.761x52.8758,-123.637x40.1722,-127.159x27.0285,-129.288x13.5887,-130x0,-129.288x-13.5887,-127.159x-27.0285,-123.637x-40.1722,-118.761x-52.8758,-112.583x-65,-105.172x-76.4121,-96.6088x-86.987,-86.987x-96.6088,-76.4121x-105.172,-65x-112.583,-52.8758x-118.761,-40.1722x-123.637,-27.0285x-127.159,-13.5887x-129.288,0x-130,13.5887x-129.288,27.0285x-127.159,40.1722x-123.637,52.8758x-118.761,65x-112.583,76.4121x-105.172,86.987x-96.6088,96.6088x-86.987,105.172x-76.4121,112.583x-65,118.761x-52.8758,123.637x-40.1722,127.159x-27.0285,129.288x-13.5887,130x0 before_layer_gcode = end_gcode = M104 S0 ; turn off temperature\nM140 S0\nG91\nG1 Z10 E-5.0 F12000\nG90\nG28 \nM84 ; disable motors extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.5 octoprint_apikey = 1589B335DF114E36B8EC3B48EF13A167 octoprint_host = 192.168.9.111:80 pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 0 retract_length = 4 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0.1 retract_restart_extra_toolchange = 0 retract_speed = 40 start_gcode = M104 S[temperature]\n\nM190 S[bed_temperature]\n\nM109 S[temperature]\n\nG28 toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 1 z_offset = 0 [printer:Rostock - Wood] bed_shape = 129.288x13.5887,127.159x27.0285,123.637x40.1722,118.761x52.8758,112.583x65,105.172x76.4121,96.6088x86.987,86.987x96.6088,76.4121x105.172,65x112.583,52.8758x118.761,40.1722x123.637,27.0285x127.159,13.5887x129.288,0x130,-13.5887x129.288,-27.0285x127.159,-40.1722x123.637,-52.8758x118.761,-65x112.583,-76.4121x105.172,-86.987x96.6088,-96.6088x86.987,-105.172x76.4121,-112.583x65,-118.761x52.8758,-123.637x40.1722,-127.159x27.0285,-129.288x13.5887,-130x0,-129.288x-13.5887,-127.159x-27.0285,-123.637x-40.1722,-118.761x-52.8758,-112.583x-65,-105.172x-76.4121,-96.6088x-86.987,-86.987x-96.6088,-76.4121x-105.172,-65x-112.583,-52.8758x-118.761,-40.1722x-123.637,-27.0285x-127.159,-13.5887x-129.288,0x-130,13.5887x-129.288,27.0285x-127.159,40.1722x-123.637,52.8758x-118.761,65x-112.583,76.4121x-105.172,86.987x-96.6088,96.6088x-86.987,105.172x-76.4121,112.583x-65,118.761x-52.8758,123.637x-40.1722,127.159x-27.0285,129.288x-13.5887,130x0 before_layer_gcode = end_gcode = M104 S0 ; turn off temperature\nM140 S0\nG91\nG1 Z10 E-5.0 F12000\nG90\nG28 \nM84 ; disable motors extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.5 octoprint_apikey = 1589B335DF114E36B8EC3B48EF13A167 octoprint_host = 192.168.9.111:80 pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 0 retract_length = 7 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 95 start_gcode = M104 S[temperature]\n\nM190 S[bed_temperature]\n\nM109 S[temperature]\n\nG28 toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 1 z_offset = 0 [printer:Ultimaker 2] bed_shape = 0x0,223x0,223x223,0x223 before_layer_gcode = end_gcode = G28 ; home all\nM104 S0 ; turn off heaters\nM140 S0 ; turn off bed\nM84 ; disable motors extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.4 octoprint_apikey = 672B8BCE1CD6427E8CD9CE77E9D52B51 octoprint_host = 192.168.9.112 pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 5 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 40 start_gcode = G28 ; home all axes\nG1 X110 Y45 F3000 ; bring extruder to the front\nG92 E0 ; zero the extruded length\nG1 Z30 ; lower\nG1 E50 F225 ; purge nozzle with 50mm of filament\nG1 X80 Y60 F3000 ; move aside of the puddle of primed plastic\nG92 E0 ; zero the extruded length again toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 1 z_offset = 0 [printer:Ultimaker 2-test] bed_shape = 0x0,223x0,223x223,0x223 before_layer_gcode = end_gcode = G91 ; relative coordinates \nG1 Z0.2 ; retract lift \nG1 E-20 F3000 ; reverse priming \nG90 ; absolute coordinates \nG28 ; home all axes \nM104 S0 ; turn off extruder heaters \nM140 S0 ; turn off bed heater \nM84 ; disable motors extruder_offset = 0x0 gcode_flavor = reprap layer_gcode = nozzle_diameter = 0.4 octoprint_apikey = 672B8BCE1CD6427E8CD9CE77E9D52B51 octoprint_host = 192.168.9.112 pressure_advance = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 4.5 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 40 start_gcode = G28 ; home all axes \nG1 F12000 X5 Y10 ; Cura HEATUP_POSITION_COMMAND \nM190 S[first_layer_bed_temperature] ; wait for bed temperature to be reached \nM109 S[first_layer_temperature] ; wait for temperature to be reached \nG1 F2400 Z20 ; bring plate to Cura PRIMING_HEIGTH with Cura HOMING_FEEDRATE \nG92 E0 ; zero the extruded length \nG1 F500 E20 ; undo end of print/abort retraction \nG92 E0 ; zero the extruded length \n;G1 F50 E5 ; additional priming ; not neccessary\nG1 F2400 X20 Y20 Z0.3 ; wipe start position \nG92 E0 ; zero the extruded length \nG1 F225 X35 E2 ; move 15mm and extrude \nG92 E0 ; zero the extruded length \nG1 F2100 X50 E1 ; move 15mm \nG92 E0 ; zero the extruded length toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 1 z_offset = 0 [settings] autocenter = 1 mode = expert [simple] avoid_crossing_perimeters = 1 bed_shape = 0x0,180x0,180x180,0x180 bed_temperature = 0 before_layer_gcode = bottom_solid_layers = 3 bridge_acceleration = 0 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = 0 cooling = 1 default_acceleration = 0 disable_fan_first_layers = 3 dont_support_bridges = 1 duplicate_distance = 6 end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 50% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 0 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.75 fill_angle = 45 fill_density = 20% fill_pattern = honeycomb first_layer_acceleration = 0 first_layer_bed_temperature = 0 first_layer_extrusion_width = 200% first_layer_height = 0.35 first_layer_speed = 30 first_layer_temperature = 205 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 0 infill_every_layers = 10 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 80 interface_shells = 0 layer_gcode = layer_height = 0.25 max_fan_speed = 100 max_print_speed = 80 max_volumetric_speed = 0 min_fan_speed = 35 min_print_speed = 10 min_skirt_length = 0 notes = nozzle_diameter = 0.35 octoprint_apikey = octoprint_host = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 3 post_process = pressure_advance = 0 raft_layers = 0 resolution = 0 retract_before_travel = 2 retract_layer_change = 0 retract_length = 2 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 40 seam_position = aligned skirt_distance = 6 skirt_height = 1 skirts = 1 slowdown_below_layer_time = 5 small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n support_material = 0 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 60 support_material_threshold = 0 temperature = 200 thin_walls = 1 threads = 2 toolchange_gcode = top_infill_extrusion_width = 0 top_solid_infill_speed = 15 top_solid_layers = 3 travel_speed = 130 use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 xy_size_compensation = 0 z_offset = 0e = 0 retract_before_travel = 2 retract_layer_change = 1 retract_length = 4.5 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 40 start_gcode = G28 ; home all axes \nG1 F12000 X5 Y10 ; Cura HEATUP_POSITION_COMMAND \nM190 S[first_layer_bed_temperature] ; wait for bed temperature to be reached \nM109 S[first_layer_temperature] ; wait for temperature to be reached \nG1 F2400 Z20 ; bring plate to Cura PRIMING_HEIGTH with Cura HOMING_FEEDRATE \nG92 E0 ; zero the extruded length \nG1 F500 E20 ; undo end of print/abort retraction \nG92 E0 ; zero the extruded length \n;G1 F50 E5 ; additional priming ; not neccessary\nG1 F2400 X20 Y20 Z0.3 ; wipe start position \nG92 E0 ; zero the extruded length \nG1 F225 X35 E2 ; move 15mm and extrude \nG92 E0 ; zero the extruded length \nG1 F2100 X50 E1 ; move 15mm \nG92 E0 ; zero the extruded length toolchange_gcode = use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 1 z_offset = 0 [settings] autocenter = 1 mode = expert [simple] avoid_crossing_perimeters = 1 bed_shape = 0x0,180x0,180x180,0x180 bed_temperature = 0 before_layer_gcode = bottom_solid_layers = 3 bridge_acceleration = 0 bridge_fan_speed = 100 bridge_flow_ratio = 1 bridge_speed = 60 brim_width = 0 complete_objects = 0 cooling = 1 default_acceleration = 0 disable_fan_first_layers = 3 dont_support_bridges = 1 duplicate_distance = 6 end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n external_fill_pattern = rectilinear external_perimeter_extrusion_width = 0 external_perimeter_speed = 50% external_perimeters_first = 0 extra_perimeters = 1 extruder_clearance_height = 20 extruder_clearance_radius = 20 extruder_offset = 0x0 extrusion_axis = E extrusion_multiplier = 1 extrusion_width = 0 fan_always_on = 0 fan_below_layer_time = 60 filament_colour = #FFFFFF filament_diameter = 1.75 fill_angle = 45 fill_density = 20% fill_pattern = honeycomb first_layer_acceleration = 0 first_layer_bed_temperature = 0 first_layer_extrusion_width = 200% first_layer_height = 0.35 first_layer_speed = 30 first_layer_temperature = 205 gap_fill_speed = 20 gcode_arcs = 0 gcode_comments = 0 gcode_flavor = reprap infill_acceleration = 0 infill_every_layers = 10 infill_extruder = 1 infill_extrusion_width = 0 infill_first = 0 infill_only_where_needed = 0 infill_overlap = 15% infill_speed = 80 interface_shells = 0 layer_gcode = layer_height = 0.25 max_fan_speed = 100 max_print_speed = 80 max_volumetric_speed = 0 min_fan_speed = 35 min_print_speed = 10 min_skirt_length = 0 notes = nozzle_diameter = 0.35 octoprint_apikey = octoprint_host = only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base].gcode overhangs = 1 perimeter_acceleration = 0 perimeter_extruder = 1 perimeter_extrusion_width = 0 perimeter_speed = 60 perimeters = 3 post_process = pressure_advance = 0 raft_layers = 0 resolution = 0 retract_before_travel = 2 retract_layer_change = 0 retract_length = 2 retract_length_toolchange = 10 retract_lift = 0 retract_restart_extra = 0 retract_restart_extra_toolchange = 0 retract_speed = 40 seam_position = aligned skirt_distance = 6 skirt_height = 1 skirts = 1 slowdown_below_layer_time = 5 small_perimeter_speed = 15 solid_infill_below_area = 70 solid_infill_every_layers = 0 solid_infill_extruder = 1 solid_infill_extrusion_width = 0 solid_infill_speed = 20 spiral_vase = 0 standby_temperature_delta = -5 start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n support_material = 0 support_material_angle = 0 support_material_contact_distance = 0.2 support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 support_material_interface_extruder = 1 support_material_interface_layers = 3 support_material_interface_spacing = 0 support_material_interface_speed = 100% support_material_pattern = pillars support_material_spacing = 2.5 support_material_speed = 60 support_material_threshold = 0 temperature = 200 thin_walls = 1 threads = 2 toolchange_gcode = top_infill_extrusion_width = 0 top_solid_infill_speed = 15 top_solid_layers = 3 travel_speed = 130 use_firmware_retraction = 0 use_relative_e_distances = 0 use_volumetric_e = 0 vibration_limit = 0 wipe = 0 xy_size_compensation = 0 z_offset = 0
