Difference between revisions of "Woodshop Area"
Mike Hutton (talk | contribs) |
Jens Torell (talk | contribs) |
||
Line 149: | Line 149: | ||
| [[User:Charles Timmons|Charles Timmons]] || 10/14/15|| | | [[User:Charles Timmons|Charles Timmons]] || 10/14/15|| | ||
|- | |- | ||
− | | [[User:Kim | + | | [[User:Kim Lujan|Kim Lyjan]] || 09/28/15|| |
|- | |- | ||
| [[User:Paul Wilson|Paul Wilson]] || 10/14/15|| | | [[User:Paul Wilson|Paul Wilson]] || 10/14/15|| |
Revision as of 12:07, 22 November 2015
Contents
General Information
MakeICT's woodshop is an enclosed 32'x36' (1152 sq ft) air conditioned area dedicated to wood working.
Mike Hutton is the Benevolent Dictator over the woodshop.
The goal of the shop space is to encourage continued learning of the skills needed to further your knowledge of woodworking!
Machine Access Policy
Approved by the Board of Directors September 18, 2015
Because of the hazardous nature of these tools, before anyone can use the tools, they must pass a regularly scheduled shop safety course that will be posted on the calendar. We want everyone to go home safe and in one piece! SAFE OPERATION of tools is top priority.
Anyone entering the shop will be required to use personal protective equipment (PPE) such as safety glasses, hearing protection, and possibly dust masks (these will be available for purchase).
To protect machinery as well as to protect other members, only domestic lumber or veneer or WELL INSPECTED reclaimed lumber free of sand, gravel, nails, screws, staples or finish will be allowed in the shop, pressure treated lumber is hazardous and will not be allowed any time. Some people are allergic to certain lumber and have become sensitized to being near the materials, therefore no exotic lumber or veneer (such as the rosewood family, cocobolo, spalted, etc) will be allowed in the shop to protect all members. When in doubt, ask.
It is HIGHLY recommended that we use a buddy system, where no single person is working in the shop without a second person in the building so that if there is an injury, somebody else is there to call for help or assist you.
General Shop Safety
- Do not use any machine you are not trained on and comfortable using. If at any time you are unsure of what you are doing, stop immediately and ask for help. Do not force tools.
- Do not use any machine that is not in good working order. Stop, unplug and leave a note on the machine and notify the woodshop BD.
- NEVER ASSUME A TOOL IS PROPERLY ADJUSTED. Always check the tool prior to use.
- Wear safety glasses at all times when in the shop area, including near the machine shop.
- Ear protection is also recommended, many of the tools operate above 90 decibels and without protection, you are losing hearing.
- When using power tools (including hand power tools):
- No open-toed shoes or loose clothing (remove drawstrings)
- Remove objects on hands and wrists (including rings, bracelets, & watches)
- Remove dangly necklaces, hair ornaments, and earrings
- Restrain long hair to prevent entanglement
- Do not wear gloves when operating machinery
- While hand tools are safer than most power tools, they are the cause of most workshop injuries. Make sure all hand tools are sharp and in good condition. Be certain that you know how to use these tools in a way that is safe, effective, and will not damage the tool.
- Do not leave machines running unattended.
- Never talk to or disturb anyone operating power tools. If you must talk to an operator wait until the operator notices you.
- Be aware of the work going on around you. Do not accidentally bump into another person or their materials while they are working.
- Most shop accidents are caused by working tired, rushed or distracted. As you get more experience, you will learn to listen to the little voice in the back of your mind that says, you probably shouldn't do that. Stop and think, there is usually a safer way of performing that function. These machines do not have a brain, please use yours!
Woodshop Specific Safety
- All powered woodcutting and sanding tools must be run with dust collection or vacuum equipment connected to the appropriate ports and on at all times. Do not switch the dust collector on and off without time to cool, if you are planning on working with multiple tools, leave the collector on (repeated quickly turning on and off will overheat the motor).
- Smoke or sparks are bad signs in the woodshop. Stop what you are doing and correct the problem. Usually correct feed and depth of cut or getting a sharp bit / blade will help.
- No metal cutting allowed on woodshop equipment.
- No wet or damp items of any type (including drink containers, rags, or hands) may be placed or left on machine surfaces as they will corrode.
- Do not lean or sit on machinery, these are precision pieces of equipment and you can mis-align them.
- You are responsible for cleaning your machines, your work space, and putting all tools away immediately after use. Scrap wood should be placed in designated locations. Use vacuums or hand brushes to clean machinery.
- Users who consistently fail in their clean-up responsibilities may be denied shop access.
- Do not use stationary equipment work surfaces for sanding, project assembly, layout, applying finishes, etc. Or for uses other than their intended purpose.
- Make sure machines are in the “off” position and motion has stopped, before leaving them after use.
- All safety guards must be kept in place while operating equipment. If a guard or safety device is an impediment to safe operation of a machine - ask for help.
- Use equipment only for its intended use.
- If you have made an adjustment to a piece of equipment, return it to its normal position after you are done.
- Make sure the machine’s work surface is unobstructed and clean before use.
- Always be aware of the proximity of moving machine parts to body parts - fingers.
- Defects in the wood can be dangerous. Check the stock carefully for knots, splits, and other defects.
- Keep the machine clean. Remove all tools, lumber, and unnecessary materials.
- Objects left on the machine can vibrate into revolving cutters. They can then be thrown from the machine with great force. Never clean a machine while it is running.
- All guests are the responsibility of the member, guests are not allowed to use equipment. This is a working shop, so children less than 7 years old are not allowed for safety.
- Member will be responsible for replacing the blade and Sawstop brake if the brake is fired for anything other than a true safety firing. If it is a true safety firing, we will need a photo of the fresh wound and SawStop will evaluate the recorded cartridge memory. If SawStop deems it to be a safety firing, they will need the photo and a release for marketing use and they send a replacement cartridge.
This is a video on table saw kickback. Do not try this in the woodshop!
Equipment List
Picture | What | Manufacturer | Model | Power | Status | Expert |
---|---|---|---|---|---|---|
![]() |
10" Cabinet Table Saw | Saw Stop | Professional PCS31230 | 220 | Operational | Mike Hutton |
![]() |
8" Carbide Helical Head Jointer | Shop Fox | W1741S | 220 | Operational | Mike Hutton |
![]() |
15" Carbide Helical Head Planer | Jet | JWP-15HH | 220 | Operational | Mike Hutton |
![]() |
17" Drill Press with laser | Jet | JDP-17DX | 110 | Operational | Mike Hutton |
![]() |
Oscillating Spindle Sander | Jet | JBOS-5 | 110 | Operational | Mike Hutton |
![]() |
Low Speed 8" Bench Grinder | Jet | JWBG-8 | 110 | Operational | Mike Hutton |
![]() |
Tool Sharpener | Work Sharp | WS3000 | 110 | Operational | Mike Hutton |
![]() |
8" Buffer for Honing | Central Machinery | 40668 | 110 | Operational | Mike Hutton |
![]() |
Cyclone Dust Collector | Oneida Air | 5HP Super Dust Gorilla | 220 | Operational | Mike Hutton |
![]() |
20" Scroll Saw | Dewalt | DW788 | 110 | Operational | Mike Hutton |
![]() |
16" Scroll Saw | Delta | 40-560, TY II | 110 | Operational | Mike Hutton |
![]() |
2.25HP Router | Bosch | 1617EVSPK | 110 | Operational | Mike Hutton |
![]() |
2" 18Gauge Finish Nailer | Hitachi | NT50AE2 | Air | Operational | Mike Hutton |
![]() |
Router Table with JessEm Lift | Porter Cable | 7518 | 110 | Operational | Mike Hutton |
![]() |
12" Double Bevel Miter Saw | Dewalt | DW705 | 110 | Operational | Mike Hutton |
![]() |
6x48 Belt/12 Disc sander | PowerMatic | 30b | 110 | Operational | Mike Hutton |
![]() |
1x30 Belt/5 Disc sander | Dremel | 1731 | 110 | Operational | Mike Hutton |
![]() |
14" Bandsaw | Rockwell | 14" Enclosed Base | 110 | Operational | Mike Hutton |
![]() |
17" Bandsaw Extreme Series | Grizzly | G0513X2 | 220 | Operational | Mike Hutton |
![]() |
12x36 Wood Lathe | Rockwell | 110 | Operational | Mike Hutton | |
File:ShopBot.jpg | 4'x 8' 3 Axis CNC Router | ShopBot | PRT 96 | 110 | Being configured | Chris Butcheller |
![]() |
5HP 60 gal Compressor | Ingersoll Rand | SS5L5 | 220 | Operational | Mike Hutton |
Certified Members
Name | Certification Date | Notes |
---|---|---|
Mike Hutton | 09/23/15 | Woodshop BD |
Larry Roth | 09/23/15 | Woodshop instructor |
Bryan Barr | 09/23/15 | Fab Lab BD |
Jess Bechtelheimer | 09/28/15 | Arts BD |
Tom McGuire | 09/28/15 | |
David Springs | 09/23/15 | |
Recil Robinson | 09/23/15 | |
Barry Wright | 09/23/15 | |
Jessica Jones | 09/26/15 | |
Robert Irons | 09/26/15 | |
David Hammond | 09/26/15 | |
Clay Hammond | 09/26/15 | |
Brad Cooley | 09/26/15 | |
James Classen | 09/28/15 | |
John Alexander | 09/28/15 | |
Charles Timmons | 10/14/15 | |
Kim Lyjan | 09/28/15 | |
Paul Wilson | 10/14/15 | |
Derek Alexander | 10/14/15 | |
Michael Barrett | 10/14/15 | |
Jerry Carpenter | 09/23/15 | Wood Shop instructor |
Clark Schultz | 09/23/15 | Safety Sultan |
Jens Torell | 09/23/15 | VP MakeICT |
Chris Batcheller | 09/23/15 | ShopBot Dude |
Mike Doolittle | 09/26/15 | Classroom BD |
Dustin Richey | 09/28/15 | Treasurer |
Santhosh Subramanian | 09/26/15 | |
Thomas Bloom | 09/26/15 | |
Logan Pajunen | 09/26/15 | |
Chuck Surland | 09/26/15 | |
Jane Teter | 09/26/15 | |
Karen Callanan | 09/26/15 | |
Dana Danaver | 09/28/15 | |
Curt Gridley | 09/28/15 | Tormach Dude |
Geoffrey Kisch | 09/28/15 | |
Kathryn Vernon | 09/26/15 | |
Christian Kindel | 09/23/15 | |
Samuel McConnell | 10/14/15 | |
Andy Solter | 10/14/15 | |
Taylor Johnson | 10/14/15 | |
Mike Conklin | 10/25/15 | |
Brian Scheideman | 10/25/15 | |
Jon Treas | 10/25/15 | |
Chuck Griesel | 10/25/15 | |
Jesse Lee | 10/25/15 | |
Samuel Schurter | 11/17/15 | |
Jane Voelkel | 11/17/15 | |
Barb Davis | 11/17/15 | MakeICT Board member |
Jeremiah Loder | 11/17/15 | |
Marc Lujan | 11/17/15 | |
Miles McClure | 11/17/15 | |
Teresa McClure | 11/17/15 | |
Weston Vice | 11/17/15 | |
Chris DeVries | 11/17/15 | |
Iylland Smith | 11/17/15 | |
Daniel Towle | 11/17/15 |