Electronics and Rapid Prototyping

Attention! This page or section is out of date. Help us out by modifying this page.
Details: missing details and access policies

General Information

MakeICT's Electronics and Rapid Prototyping lab is an enclosed 200 sq ft area. This area has several dedicated spaces. One is for creation of electronics, including a board milling machine, area dedicated for assembly, and reflow oven. Another is for the troubleshooting of electronics, including a hot air rework station, Spectrum Analyzer, Oscilloscope, current limited power supply, and logic analyzer. We have a pair of CNC machines fully capable of handling wood, and some aluminum. We offer Dremmel sets to handle less delicate work (or more delicate depending on your skill.) We also have systems one can check out for the learning of electronics, toolsets to fix and repair, as well as Chip programmers, a bus pirate, Raspberry Pis, Arduinos, even a pic based USB module. We offer a full components library, resplendent with analogue devices, TTL type logic, some rare chipsets, and a full complement of passives. The hackables library is also located here. Here is where you may find the inspiration and starting point for your next blue ribbon hack. This lab is dedicated to creating and debugging electronics, as well as some rapid prototyping capabilities. Never a room to be bored in, the common complaint in this room is, "what do I make first?"

James Seymour is the Benevolent Dictator over the electronics and rapid prototyping lab.

Borrowing Items

Currently we do not lend out equipment, but as we build up an inventory of certain items, we may allow checkout similar to a library. Special arrangements may be made on a individual basis, but that is entirely up to the BD.

Items for Purchase

We do have certain items for sale. Sales should be considered final, the money goes back into the ERP Lab.

Hackables Policy

Items donated to the space with the intent of being hacked (or reused in a way that it was not originally intended) should be placed on the middle shelf that is labeled "HACKABLES" by the back door. If there is no room on the shelf try rearranging things to make it fit. If that's not possible please take your items home until some space gets cleared out on the shelf. Every two weeks or as needed a message will be posted on the group list that the shelf will be cleared. Any items on the Hackables shelf are up for grabs by any member. If you just need a part out of a hackable you don't have to take the whole thing. Just place the remainder back on the shelf for someone else to hack. But if there's really nothing good left in it please throw it away.Items that are considered to have long term hackable value can be moved to other work areas with permission of the areaBD. For instance circuit boards that have parts on them that are generally good for circuit building projects can be moved to the ERP area hackables shelves. The ERP lab BD maintains the hackables inventory. Hackables are up for grabs and may be removed from the shelves at any time. Any questions about hackables can be refereed to the current BD.

Component Library

MakeICT maintains an electronics library. There is currently no inventory of available components. Components in the library are for member use, We only ask you put a buck or two in the donation bucket if you use a lot of them, or some of the rare/complex parts.

Classes

• Basic Electronics Workshop
• Circuit Design and Fabrication
• Rapid Prorotyping with CNC
• Basic Soldering Class

Machine Access Policy

Clean up! Users are responsible for clean up after themselves; failure to which may result in loss of E&RP Privileges, and may require corrective training to regain those privileges. Corrective training is up to the BD, and he is very creative. This is not just limited to the CNC machines. We try to keep everything in the room orderly. when you are done with a cable, attenuator, milling bit, Multimeter, put it back please. If it turns on, turn it off. This way we can spend less money on overhead, and more money on toys... ahem... equipment.

Scopes

MakeICT has a few Oscilloscopes. Most notably is the Tektronix 465B We are fortunate to have some nice ones. Using the Oscilloscope takes some finesse and it's best you have some help with it if you're fairly new to one, so we require certification. The Oscilloscope shows Voltage over time, similar to a graph. There is lots of settings, dials, and switches. if you want to learn to use it just ask to be taught from a reasonably knowledgeable member.

• List of known Scope users is listed below
  • Tom McGuire
  • James Seymour

Spectrum Analyzer

We have a very nice Spectrum Analyzer (Tektronix 492 AP). The Spectrum Analyzer shows receive power over frequency. So if you set it properly you would see Peaks where each Wifi network is transmitting. It is easy (and expensive) to damage the input of a Spectrum Analyzer. We ask you are certified and use proper caution. We have several attenuators available for impedance matching, so use them.

• List of known analyzer users is listed below
  • James Seymour

Circuit Design and Fabrication

Use of the Board Goblin-Circuit Board Mill and or SMD Circuit Work Station requires attendance in the Circuit Design and Fabrication or certification from an approved peer-certifier. We do not mind if your circuit doesn't work, we do mind if our equipment doesn't.

• Any member who has been certified to use the circuit fabrication equipment may peer-certify other members
• Certification instruction must at least include
  • Fundamental knowledge of circuit board milling principles
  • Fundamental knowledge of soldering and solder reflow
  • Proper use and control of the LinuxCNC software
  • Basic circuit design
• Certification must be documented (link to instructions or form) prior to use
• List of circuit fabrication users below
  • Tom McGuire

V90 CNC router

Use of the V90 CNC router requires attendance in CNC Router certification workshop

• Certification must be documented (link to instructions or form) prior to use
• List of CNC Router Certified users is listed below
  • Tom McGuire

'The Beast' RD-500S II rework Machine

The Beast isn't up and running yet. It requres some TLC and is considered a work in progress. Once operational, it is designed to make short work of SMD replacement, by combining a CNC rework station with an on board reflow process. Operation will be mostly peer Certification.

Electronics and Rapid Prototyping Safety

1. Do not use any machine you are not trained on and comfortable using. If at any time you are unsure of what you are doing, stop immediately and ask for help.
2. Do not use any machine that is not in good working order. Stop, unplug and leave a note on the machine and notify the BD OR Tom McGuire.
3. NEVER ASSUME A TOOL IS PROPERLY ADJUSTED. Always check the tool prior to use.
4. NEVER MODIFY OR HACK MACHINERY WITHOUT CONSENT FROM THE AREA BD.
5. Always triple check your inputs when connecting to equipment. Dangerous levels are dangerous.

Equipment List

Picture	What	Manufacturer	Model	Power	Status	Expert
	Various types and brands	Various	Soldering Iron	110	Working	James Seymour
	RD-500S II Area Array Rework System	Den-on Instruments	RD-500S II	110	Not yet	James Seymour
	Logic Analyzer	Tektronix	1240	110	Working	James Seymour
	Tektronix 492 AP	Tektronix	492P	110	Working	James Seymour
	Oscilloscope	Tektronix	465B	110	Working	James Seymour
	Lead Free Reflow Oven	Qinsi Technology	QS-5100	110	Working	James Seymour
	Soldering Station with Heat Gun	Arksen	992D	110	Working	James Seymour
	Board Goblin-Circuit Board Mill	Tom McGuire	47158	110	Working	Tom McGuire
	7" x 10" Metal Lathe	Central Machinery	33684	110	Working	??
	Fireball V90	Probotix	Fireball V90	110	Working	Tom McGuire
	Sherline CNC Mill	Sherline	????	110	Working?
	SPECO PSV-5	SPECO	PS-5	110	Under Repair [[SPECO PSV-5 repair log

• Policies may change with the needs of the department and may go into affect before this page is updated to reflect it.