3D Printing

From MakeICT Wiki
Jump to navigationJump to search

About

3D printing is an additive manufacturing process that allows for the creation of real-world, tangible objects from 3D virtual models. MakeICT maintains three separate 3D printers, a RepRap Prusa Mendel: an Ultimaker 2, and a Rostock Max V2. Full details and specifications can be found on the individual equipment pages.

RepRap Prusa Mendel Ultimaker 2 Rostock Max v2
Build volume 180 x 180 x 100ish mm 223 x 223 x 205 mm 260 (circle) x 375 mm
Max Nozzle Temperature 250 C 250 C 295 C
Filament types PLA PLA, ABS, CPE PLA, ABS
Filament diameter 1.75 mm 2.85 mm 1.75 mm
X/Y resolution 0.125 mm 0.125 mm 0.1 mm
Z resolution .0039 mm 0.02 mm 0.0125 mm
Nozzle diameter 0.35 mm 0.4 mm 0.5 mm
Heated bed No Yes Yes (it's slow!)

Machine Access Policy

Use of the 3D printers requires attendance in a 3D printer certification workshop or certification from an approved peer-certifier.

  • Any member who has been certified to use the 3D printer may peer-certify other members
  • Certification instruction must at least include
    • Fundamental knowledge of each printer's working principles
    • Proper use and control of each printer
    • Software workflow
    • How to change filament
    • How to pay for material

Filament Fund

Printing with filament provided by MakeICT costs $0.04 per gram. After printing, please weigh your print using the provided scale and put the appropriate amount of money in the filament fund jar. If you have any requests for new colors/types of filaments, you can write them on the same jar.

Workflow

Note: This process is under development and may change. Check back here for updates if something changes.

Slicing

Slicing is the process of converting an STL file to the G-Code required to run the printer.

Any slicer with an appropriately configured profile can be used to generate G-Code to run the machines. We have setup Slic3r with profiles for each machine on the design computer in the Fab Lab, and are working to configure the same for Cura. These profiles will be uploaded to the Wiki.

Slic3r has native support for uploading to Octoprint, just hit the 'Upload to printer' button in the 'Plater' tab. In Cura just export the G-Code file and upload it using the file browser in Octoprint.

When slicing, be sure to use the correct profile for the machine you intend to print on. G-Code generated for one machine WILL NOT work properly on the others.

Printing

Each printer can be run using Octoprint. Thorough instructions on this interface can be found on the Octoprint page. The Ultimaker also has a built-in interface for printing from an SD card. Instructions for that interface can be found on the Ultimaker 2 Wiki page.

The printers can be reached at the following addresses while connected to the network at MakeICT:

The username and password are 'maker'. To run a print upload your G-Code file using the file browser on the bottom left of the page, then click the print button when the file is done uploading.

General Use Tips

  • When changing from a filament that prints hotter to one that prints cooler (e.g. ABS to PLA) you should do a cold pull to remove the old plastic that is lining the melt chamber. Otherwise there will likely be problems with underextrusion due to the unmelted plastic.
  • When your print is finished, do not immediately turn off the power; wait until the nozzle has cooled. The Ultimaker and Rostock have actively cooled heatsinks on their hotends, and if power is cut before the nozzle is cool the filament can melt higher up than intended and cause a jam.

3D Printer Authorized Users

To see authorized users expand this section --->

Name Authorization Date Authorized By
Abishek Gomes 2015-12-19 Dominic Canare
Adam Wiley 2016-03-30 Christian Kindel
Alec Wilford 2015-12-17 Dominic Canare
Anna Lenhart Murray 2016-06-01 James Lancaster
Audrey Barba 2016-06-15 James Lancaster
Barry Wright 2015-12-19 Dominic Canare
Brian Bush 2016-06-09 James Lancaster
Brock Milford 2015-12-15 Dominic Canare
Bryan Barr
Cat Barba-Abay 2015-12-17 Dominic Canare
Chris Batcheller 2015-12-19 Dominic Canare
Chris DeVries 2015-12-15 Dominic Canare
Christian Kindel
Daniel Towle 2015-12-15 Dominic Canare
Derek Alexander 2015-12-19 Dominic Canare
Dominic Canare James Lancaster
Dustin Richey
Elaine Hanna 2015-12-17 Dominic Canare
James Lancaster
James Seymour 2016-06-01 James Lancaster
John Alexander 2016-3-21 Mike Barushok
Jeff Eck
Jim Hammer 2015-12-15 Dominic Canare
Kip Landwehr
Marcia Stevens 2015-12-17 Dominic Canare
Marcus Mosley 2015-12-19 Dominic Canare
Mark Esau 2015-12-15 Dominic Canare
Matthew Warren 2015-12-15 Dominic Canare
Mike Barushok 2015-11-21
Mike Doolittle
Bob Jackson 2015-12-15 Dominic Canare
Reed Schimmel 2016-3-21 Mike Barushok
Sam McConnell 2015-11-24 Dominic Canare
Sam Schurter 2015-12-15 Dominic Canare
Steffin Gomes 2015-12-19 Dominic Canare
Steve Querbach 2015-12-19 Dominic Canare
Tom McGuire
Turquoise Thomas-Morales 2016-5-31 James Lancaster
Westin Vice 2015-12-15 Dominic Canare
Wilburt Guymon 2015-12-15 Dominic Canare
William Davisson 2015-12-15 Dominic Canare
Zach Puls 2015-11-24 Dominic Canare
Eric Sommer 2016-05-01 Christian Kindel
Rustin Atkeisson 2016-05-01 Christian Kindel
Logan Pajunen 2016-05-01 Sam McConnell